$12.00$56.00

The WetLink Penetrator is a compression gland cable penetrator to seal electrical cables as they pass into a device or enclosure. Each set includes a bulkhead, seal, plug, O-ring, and nut. It’s rated to 950 meter (3,116 feet) water depth when used with tested cables! We recommend the WetLink Plug Wrench and WetLink Assembly Block to ease with assembly!

Some cable diameters have multiple bulkhead sizes available—make sure to select the correct size for your application! M10 bulkheads fit into the pre-made holes in most of our enclosure end caps, while M6 bulkheads use smaller holes, and M14 bulkheads use larger ones.
SKU: WLP-VP
HS Code: 7616.10.7030

Product Description

The WetLink Penetrator (WLP) is our patent-pending, next-generation solution for low-cost, high pressure, high reliability sealing of electrical cables as they pass into enclosures or other devices. It’s rated to a depth of 950 meters (3,116 feet) and compared to subsea connectors or penetrators, the WetLink Penetrator is a fraction of the cost while offering validated reliability that you can count on.

The WetLink Penetrator can be installed in seconds and doesn’t require any adhesives, potting compounds, or rubber molding. It’s the easiest to use solution out there!

The concept behind the WetLink Penetrator is simple: a cable and rubber seal are installed into a bulkhead and then compressed such that a high-pressure seal is formed. That pressure also holds the cable in place and strain relieves it against it being tugged or pulled out.

Despite the simplicity of the concept, we’ve put a lot of attention into the details to ensure absolute reliability. The WetLink Penetrator was put through a rigorous testing and validation process in which we tested thousands of samples through extreme conditions: high pressure, hot and cold temperatures, high electrical current, accelerated aging, and mechanical strain. Our results demonstrate reliability that you can count on in your application.

The WetLink Penetrator can be used on a variety of cables, but the design has been officially tested and validated on specific cables. Our official specifications only apply when used on tested and validated cables, which you can see in the Technical Details tab. Be sure to refer to our “How to Choose a WetLink Penetrator” guide for a in-depth guide on how to select the right WetLink Penetrator for your cable.

The WetLink Penetrator can be assembled with typical hand tools, but we recommend the WLP Plug Wrench and WLP Assembly Block to ease with assembly, especially if you’ll be putting together more than a few!

Product Description

The WetLink Penetrator (WLP) is our patent-pending, next-generation solution for low-cost, high pressure, high reliability sealing of electrical cables as they pass into enclosures or other devices. It’s rated to a depth of 950 meters (3,116 feet) and compared to subsea connectors or penetrators, the WetLink Penetrator is a fraction of the cost while offering validated reliability that you can count on.

The WetLink Penetrator can be installed in seconds and doesn’t require any adhesives, potting compounds, or rubber molding. It’s the easiest to use solution out there!

The concept behind the WetLink Penetrator is simple: a cable and rubber seal are installed into a bulkhead and then compressed such that a high-pressure seal is formed. That pressure also holds the cable in place and strain relieves it against it being tugged or pulled out.

Despite the simplicity of the concept, we’ve put a lot of attention into the details to ensure absolute reliability. The WetLink Penetrator was put through a rigorous testing and validation process in which we tested thousands of samples through extreme conditions: high pressure, hot and cold temperatures, high electrical current, accelerated aging, and mechanical strain. Our results demonstrate reliability that you can count on in your application.

The WetLink Penetrator can be used on a variety of cables, but the design has been officially tested and validated on specific cables. Our official specifications only apply when used on tested and validated cables, which you can see in the Technical Details tab. Be sure to refer to our “How to Choose a WetLink Penetrator” guide for a in-depth guide on how to select the right WetLink Penetrator for your cable.

The WetLink Penetrator can be assembled with typical hand tools, but we recommend the WLP Plug Wrench and WLP Assembly Block to ease with assembly, especially if you’ll be putting together more than a few!

CAD model is of the 6.5mm WLP.

For each unit, the following items are included for the selected cable diameter size and bulkhead size.

  • 1 x WLP Bulkhead
  • 1 x WLP Plug
  • 1 x WLP Seal
  • 1 x WLP Nut
  • 1 x O-Ring

Performance Characteristics

ParameterValue
Maximum Tested Depth (seawater)¹950 m / 3116 ft
Design Lifetime¹ ²3 years or 500 cycles to rated depth
Reuse Recommendations (link)
Bulkhead and Plugreusable up to 3 times
Sealnot reusable
¹ For reference only, performance may vary depending on application and cable construction, it is the responsibility of the customer to determine suitability for their application.
² Design life was used to inform testing in an accelerated environment, does not reflect warranty period.

Size Index

Seal SizeBulkhead SizesConductor Bore DiameterPlug CompressionJacket Diameter RangePart NumberDiagram
4.5M06
M10
3.3 mmHigh (HC)4.0 ± 0.3 mmWLP-M06-4.5MM-HC
WLP-M10-4.5MM-HC
Low (LC)4.5 ± 0.3 mmWLP-M06-4.5MM-LC
WLP-M10-4.5MM-LC
5.5M104.0 mmHigh (HC)
5.0 ± 0.3 mm
WLP-M10-5.5MM-HC
Low (LC)5.5 ± 0.3 mmWLP-M10-5.5MM-LC
6.5M104.8 mmHigh (HC)
6.0 ± 0.3 mm
WLP-M10-6.5MM-HC
Low (LC)6.5 ± 0.3 mmWLP-M10-6.5MM-LC
7.5M105.7 mmHigh (HC)
7.0 ± 0.3 mmWLP-M10-7.5MM-HC
Low (LC)7.5 ± 0.3 mmWLP-M10-7.5MM-LC
8.5M106.0 mmHigh (HC)
8.0 ± 0.3 mm
WLP-M10-8.5MM-HC
Low (LC)8.5 ± 0.3 mmWLP-M10-8.5MM-LC
9.5M147.5 mmHigh (HC)9.0 ± 0.3 mmWLP-M14-9.5MM-HC
Low (LC)9.5 ± 0.3 mmWLP-M14-9.5MM-LC

Tools

Seal SizeBulkhead SizeBulkhead WrenchBulkhead/Nut Flat SizeBulkhead Installation TorquePlug WrenchPlug Hex SizePlug Installation Torque
4.5M06BR-100977-00612 mm1 N⋅mBR-100369-01111 mm14 N⋅m
4.5M10BR-100977-01016 mm3.5 N⋅mBR-100369-01111 mm14 N⋅m
5.5, 6.5, 7.5, 8.5M10BR-100977-01016 mm3.5 N⋅mBR-100369-01414 mm14 N⋅m
9.5M14BR-100977-01420 mm3.5 N⋅mBR-100369-01818 mm20 N⋅m
* The WetLink Penetrator Assembly Block is compatible with all WetLink Penetrator sizes

Tested Cables

Compatible WLP Part NumberCable Part Name / NumberManufacturerApplicationJacket DiameterJacket MaterialConductorsTested Current¹Nominal VoltageMax Temp Recommended²
WLP-M06-4.5MM-HC
WLP-M10-4.5MM-HC
Fathom Slim TetherBlue RoboticsTether4.0 mmPUR Foam1x UTP 26AWG--50°C
WLP-M06-4.5MM-LC
WLP-M10-4.5MM-LC
Lumen/Gripper CableBlue RoboticsPower / PWM4.5 mmPUR3x 22AWG--60°C
Ping CableBlue RoboticsPower / Serial4.5 mmPUR4x 24AWG--60°C
Ping360 CableBlue RoboticsPower / Ethernet4.7 mmPUR3x UTP 28AWG--50°C
WLP-M10-5.5MM-HCchainflex® control cable CF9
(CF9-02-06)
IGUSPower / Signal5.0 mmTPE6x 24AWG-300 V60°C
WLP-M10-5.5MM-LCEtherline® (2170283)LAPPCat5e5.6 mmPUR2x SFTP 26AWG-125 V60°C
WLP-M10-6.5MM-HCUnitronic® (302206)LAPPPower / Signal5.8 mmPVC6x 22AWG-300 V60°C
WLP-M10-6.5MM-LCT200 Thruster CableBlue RoboticsPower6.4 mmPUR3x 16AWG48 A-60°C
Etherline® (2170300)LAPPCat5e6.3 mmPUR4x SFTP 26AWG-1000 V60°C
WLP-M10-7.5MM-HCFathom ROV TetherBlue RoboticsCat5 / Tether 7.8 mmPUR Foam4x UTP 26AWG--50°C
WLP-M10-7.5MM-LCEthernet and Power CableBlue RoboticsCat5 + Power7.5 mmPUR4x UTP 26AWG + 2x 22AWG--60°C
WLP-M10-8.5MM-HCchainflex® control cable CF9
(CF9-02-12)
IGUSPower / Signal7.7 mmTPE12x 24AWG-300 V60°C
WLP-M10-8.5MM-LCHigh Power CableBlue RoboticsPower8.3 mmPUR2x 12AWG60 A-60°C
WLP-M14-9.5MM-HCT500 Thruster CableBlue RoboticsPower9.0 mmPUR3x 12AWG100 A-60°C
¹ Current ratings evaluated at ambient temperatures in water.
² Sustained high temperatures can lead to performance loss over long periods of time.

Physical Properties

Bulkhead SizeM06M10M14
Seal Sizes (A)4.54.5, 5.5, 6.5, 7.5, 8.59.5
Bulkhead Thread (B)M6 x 1M10 x 1.5M14 x 1.5
Bulkhead Thread Length (C)10 mm20 mm25 mm
Recommended Bulkhead Through Hole Size6.2 mm10.2 mm14.2 mm
Assembled Height from Endcap (D)23.5 mm18 - 26 mm23 mm
Overall Outer Diameter (E)13 mm18 mm22 mm
O-ring Size (F)1.5 x 7 mm Buna-N 70AAS568-013 Buna-N 70A1.5x15 mm Buna-N 70A
Nut Height (G)4 mm8 mm8 mm
Nut Slot Width (H)3.5 mm5 mm9 mm
Assembled air weight (no cable)7.6 g13.9 - 15.6 g24.9 g
Assembled water weight (no cable)5.1 g10.2 - 10.7 g16.4 g
Seal MaterialFKM
Seal Material Temperature Range-25°C to 200°C
Bulkhead / Plug Material7075-T6 Aluminum, Anodized

Test Procedure

ParameterValue
Minimum Number of Test Samples36
Test Pressure950 msw
Number of Cycles500 cycles
Water Temperatures at Pressure2°C to 40°C
Temperature Shock Cycling in Air-30°C to 70°C
Cable Axial Strain (10 cycles)3.5 to 7.5 kg
Cable Radial & Torsional StrainingYes
Tested Current at Pressure (if applicable)Yes
1000V Hipot Test & Continuity TestYes
Accelerated Age TestYes
*Test values shown for reference only, it is the responsibility of the customer to determine suitability for their application.

3D Models

WLP-M06-4.5MM-R1 (.zip)

WLP-M10-4.5MM-R1 (.zip)

WLP-M10-5.5MM-R1 (.zip)

WLP-M10-6.5MM-R1 (.zip)

WLP-M10-7.5MM-R1 (.zip)

WLP-M10-8.5MM-R1 (.zip)

WLP-M14-9.5MM-R1 (.zip)

WL-M06-NUT-R1 (.zip)

WL-M10-NUT-R1 (.zip)

WL-M14-NUT-R1 (.zip)

Documents

WLP Technical Datasheet (.pdf)

Revision History

20 June 2023

  • WLP-M06-4.5MM-LC-R1-RP SKU changed to BR-100870-245
  • WLP-M06-4.5MM-LC-R1-5PACK-RP SKU changed to BR-100493-245
  • WLP-M10-4.5MM-LC-R1-RP SKU changed to BR-100870-045
  • WLP-M10-4.5MM-LC-R1-5PACK-RP SKU changed to BR-100493-045
  • WLP-M06-4.5MM-HC-R1-5PACK-RP SKU changed to BR-100493-345
  • WLP-M06-4.5MM-HC-R1-RP SKU changed to BR-100870-345
  • WLP-M10-4.5MM-HC-R1-5PACK-RP SKU changed to BR-100493-145
  • WLP-M10-4.5MM-HC-R1-RP SKU changed to BR-100870-145
  • WLP-M10-5.5MM-HC-R1-5PACK-RP SKU changed to BR-100493-155
  • WLP-M10-5.5MM-HC-R1-RP SKU changed to BR-100870-155
  • WLP-M10-5.5MM-LC-R1-5PACK-RP SKU changed to BR-100493-055
  • WLP-M10-5.5MM-LC-R1-RP SKU changed to BR-100870-055
  • WLP-M10-6.5MM-LC-R1-5PACK-RP SKU changed to BR-100493-065
  • WLP-M10-6.5MM-LC-R1-RP SKU changed to BR-100870-065
  • WLP-M10-6.5MM-HC-R1-5PACK-RP SKU changed to BR-100493-165
  • WLP-M10-6.5MM-HC-R1-RP SKU changed to BR-100870-165
  • WLP-M10-7.5MM-HC-R1-5PACK-RP SKU changed to BR-100493-175
  • WLP-M10-7.5MM-HC-R1-RP SKU changed to BR-100870-175
  • WLP-M10-7.5MM-LC-R1-5PACK-RP SKU changed to BR-100493-075
  • WLP-M10-7.5MM-LC-R1-RP SKU changed to BR-100870-075
  • WLP-M10-8.5MM-HC-R1-5PACK-RP SKU changed to BR-100493-185
  • WLP-M10-8.5MM-HC-R1-RP SKU changed to BR-100870-185
  • WLP-M10-8.5MM-LC-R1-5PACK-RP SKU changed to BR-100493-085
  • WLP-M10-8.5MM-LC-R1-RP SKU changed to BR-100870-085
  • WLP-M14-9.5MM-LC-R1-RP SKU changed to BR-100870-095
  • WLP-M14-9.5MM-LC-R1-4PACK-RP SKU changed to BR-100493-095
  • WLP-M14-9.5MM-HC-R1-RP SKU changed to BR-100870-195
  • WLP-M14-9.5MM-HC-R1-4PACK-RP SKU changed to BR-100493-195

19 January 2023

  • Blue bulkhead O-rings implemented

25 January 2022

  • WLP-M14-9.5MM-HC-R1 - Initial release
  • WLP-M14-9.5MM-LC-R1 - Initial release

29 November 2021

  • WLP-M06-4.5MM-HC-R1 - Initial release
  • WLP-M10-4.5MM-HC-R1 - Initial release
  • WLP-M10-5.5MM-HC-R1 - Initial release
  • WLP-M10-5.5MM-LC-R1 - Initial release
  • WLP-M10-6.5MM-HC-R1 - Initial release
  • WLP-M10-7.5MM-HC-R1 - Initial release
  • WLP-M10-7.5MM-LC-R1 - Initial release
  • WLP-M10-8.5MM-HC-R1 - Initial release
  • WLP-M10-8.5MM-LC-R1 - Initial release

8 September 2021

  • WLP-M06-4.5MM-LC-R1 - Initial release
  • WLP-M10-4.5MM-LC-R1 - Initial release

8 June 2021

  • WLP-M10-6.5MM-LC-R1 - Initial release
WetLink Penetrator Assembly Guide
The WetLink Penetrator (WLP) is our next-generation solution for low-cost, high-pressure, high-reliability sealing of electrical cables. This guide will show you how to assemble a WetLink Penetrator.
How to Choose a WetLink Penetrator
Learn how to choose the right WLP size for your cable.
Cable Stripping
Learn how to properly strip cables for use with WetLink Penetrators!

The bulkhead and plug can be re-used reliably up to 3 times. The seal must be replaced each time the penetrator is reinstalled, and the penetrator should be installed on a previously uncompressed section of the cable jacket. Please refer to our WetLink Assembly guide.

Relevant Forum Category

Blue Robotics Forums - Wetlink Products

Featured Forum Posts