WetLink Cable Splice Kit

$20.00

The WetLink Cable Splice Kit allows you to connect two cable ends without any messy potting compounds, molds, or curing time. Install WetLink Penetrators, connect the wire ends internally, and you have a splice ready to go to 500 meter depth!

Please note! WetLink Penetrators are not included, but are required to use this product.

In stock

SKU: BR-101170
HS Code: 8536.90.85.30

Product Description

The WetLink Cable Splice Kit is a revolutionary alternative to the adhesive-based splice kits that are common in subsea work. Kits like the 3M™ Scotchcast™ Cable Splicing Kits require you to mix and pour urethane potting compound into a mold and wait for it to cure. It’s a finicky process that takes time and leaves lots of room for variation and error.

The WetLink Cable Splice solves that! It’s pottingless, requires no molds, and has no cure time! You can make a high-pressure cable splice in just minutes.

This kit includes a small box, made with high-strength polycarbonate plastic, with holes on either end for the WetLink Penetrators, which seal to just about any cable with a compression gland seal. To use this kit, you’ll need a few items:

You’ll need:

Goodbye, messy potting compound! Hello, WetLink! 👋

Space inside allows for the wires to be connected with terminal or solder.
Fully assembled, the splice can handle 500m water depth!

Product Description

The WetLink Cable Splice Kit is a revolutionary alternative to the adhesive-based splice kits that are common in subsea work. Kits like the 3M™ Scotchcast™ Cable Splicing Kits require you to mix and pour urethane potting compound into a mold and wait for it to cure. It’s a finicky process that takes time and leaves lots of room for variation and error.

The WetLink Cable Splice solves that! It’s pottingless, requires no molds, and has no cure time! You can make a high-pressure cable splice in just minutes.

This kit includes a small box, made with high-strength polycarbonate plastic, with holes on either end for the WetLink Penetrators, which seal to just about any cable with a compression gland seal. To use this kit, you’ll need a few items:

You’ll need:

Goodbye, messy potting compound! Hello, WetLink! 👋

Space inside allows for the wires to be connected with terminal or solder.
Fully assembled, the splice can handle 500m water depth!
  • 1 x Cable Splice Enclosure & Lid
  • 1 x Lid O-ring
  • 2 x M3x10 Flat Head Screws
  • 1 x Molykote Pillow Pack
Please note! You’ll need two WetLink Penetrators sized for your cable diameter to use this product.

Specifications

ParameterValue
Performance
Maximum Rated Depth (seawater)500 m1640 ft
Design Lifetime¹3 years or 500 cycles to rated depth
Temperature Rating (air)-25–60°C-13–140°F
Temperature Rating (water)0–40°C32–104°F
Tools
Compatible Bulkhead WrenchBR-100977-010
Recommended Penetrator Installation Torque3.5 Nm
Lid Screw Size M3x0.5 - 10
Lid Screw Hex Key Size 2 mm
Physical
Internal Dimensions (Length x Width x Height)49 x 29 x 20 mm
Thru Hole Diameter10.1 mm
Mounting Hole Diameter 3.2 mm
Mounting Hole Spacing 32 x 60 mm
Lid O-Ring Size 44 x 1.5 mm
Wetted MaterialsPolycarbonate 30% glass-filled
Buna-N
Molykote 111 compound
Stainless steel 316
In Air Weight (No penetrators)64 g2.25 oz
In Water Weight (No penetrators)-11.2 g-0.4 oz
¹ Design life was used to inform testing in an accelerated environment, does not reflect warranty period.

2D Drawings

Drawing

3D Models

WetLink-Cable-Splice-Kit-BR-101170 (.zip)

Revision History

2 May 2023

  • BR-101170 Rev A - Initial Release

Quick Start

1. Install the WetLink Penetrator from each cable end into the holes.

2. Make all wire connections.

3. Lubricate the lid O-ring and install it on the lid.

4. Lubricate the inside surface of the enclosure and install the lid.

5. Use the lid screws and a 2 mm hex to secure the lid.

For complete instructions check out the WetLink Cable Splice Kit User Guide below.

Guides

WetLink Cable Splice Kit User Guide
The WetLink Cable Splice Kit enables quick and easy connection of two cable ends without the use of potting compounds, molds, or curing time. This guide will show you how to use the WetLink Cable Splice Kit.
WetLink Penetrator Assembly Guide
The WetLink Penetrator (WLP) is our next-generation solution for low-cost, high-pressure, high-reliability sealing of electrical cables. This guide will show you how to assemble a WetLink Penetrator.

You May Also Need

Copyright 2024 – Blue Robotics Inc
|   Terms & Conditions    |    |   Privacy Policy    |