$90.00

The Power Sense Module (PSM) provides analog current and voltage sensing to your Navigator Flight Controller or Pixhawk autopilot mounted on your BlueROV2 or custom marine robotics project.

Please note: This new revision (since September 2021) is compatible with the R3 and R4 revisions of the BlueROV2, but has changes that are not compatible with older BlueROV2s. If you need a replacement for your older BlueROV2, please contact us.

In stock

SKU: BR-101108
HS Code: 9030.33.3800

Product Description

The Power Sense Module (PSM) provides analog current and voltage sensing to your Navigator Flight Controller or Pixhawk autopilot mounted either on your BlueROV2 or custom marine robotics project. ArduSub firmware supports the Power Sense Module and through QGroundControl will give you visual indications of battery level and current consumption.

This module uses a hall effect current sensor for excellent accuracy at low current draw.

Unlike standard power modules, the Power Sense Module will NOT provide 5V power, only current and voltage sense. On the BlueROV2, the Navigator Flight Controller is powered from multiple sources so this 5V power supply is not needed.

Product Description

The Power Sense Module (PSM) provides analog current and voltage sensing to your Navigator Flight Controller or Pixhawk autopilot mounted either on your BlueROV2 or custom marine robotics project. ArduSub firmware supports the Power Sense Module and through QGroundControl will give you visual indications of battery level and current consumption.

This module uses a hall effect current sensor for excellent accuracy at low current draw.

Unlike standard power modules, the Power Sense Module will NOT provide 5V power, only current and voltage sense. On the BlueROV2, the Navigator Flight Controller is powered from multiple sources so this 5V power supply is not needed.

  • 1 x Power Sense Module with pre-installed 5.5mm bullet connectors and spade connectors
  • 1 x 200mm DF13 to JST-GH cable
  • 1 x 200mm JST-GH to JST-GH cable

Specifications

ParameterValue
Electrical
Max Voltage Input25.2 V (6S)
Max Current Sensing100 A (non-continuous)
Voltage Sense Output11.0 V/V
Current Sense Output37.8788 A/V (offset by 0.330 V)
Output ConnectorNon-insulated #6 spade
Input Connector5.5 mm bullet connector
Physical (Board Dimensions)
Length24 mm0.94 in
Width19 mm0.75 in
Height (without header pins)7 mm0.28 in
Power Pin Out
PinSignalVolt
1 (red)NOT CONNECTED
2 (blk)NOT CONNECTED
3 (blk)CURRENT+3.3 V
4 (blk)VOLTAGE+3.3 V
5 (blk)GNDGND
6 (blk)GNDGND

Documents

PSM-ELEC-PCB-R2 (.pdf)

Revision History

29 June 2023

  • PSM-ASM-R3-RP SKU changed to BR-101108

13 September 2021

  • R3 - Initial release
  • Changed 3.5 mm bullet connectors to 5.5 mm bullet connectors

12 December 2018

  • Changed XT60 connector to 3.5 mm bullet connectors

10 October 2018

  • R2 - Initial release

Quick Start

1. Follow the PSM installation instructions if installing or retrofitting a BlueROV2.
2. In the Power tab of the QGroundControl Vehicle Setup page, select “Blue Robotics Power Sense Module” for the Power Sensor.

Guides

Power Sense Module (PSM) Installation
Learn how to install and setup a Power Sense Module on your BlueROV2 or other underwater project!



Support

Blue Robotics Forums – BlueROV2

Blue Robotics Forums – ArduSub

Blue Robotics Forums – QGroundControl